-40%
ALESIS ADAT Digital Audio Recorder
$ 250.8
- Description
- Size Guide
Description
SPECIFICATIONS:Recording Format: ADAT (Alesis Digital Audio Tape)
Recording Time: 40 minutes typical per S-120 cartridge
Fast Forward/Rewind Rate: Approximately 20 times play speed unwrapped/ 10 times play speed wrapped
Fast Audio Scan Rate: Approximately 3 times play speed
Audio
Number of Audio Channels: Eight
Audio Conversion:
Record (A/D): 16 bit linear audio, Delta-Sigma 64 times oversampling , single converter per channel
Play (D/A): 18 bit linear, single converter per channel
Sample Rate: 48 kHz nominal. User variable from 50.8 to 40.4 kHz (+1, -3 semitones)
Frequency Response: 20 Hz to 20 kHz +/- 0.5 dB
Dynamic Range: Greater than 92 dB from 20 Hz-20 kHz , A weighted
Distortion: .009 % THD + Noise @ 1 kHz , 0.5 dB below maxium output, A weighted
Channel Crosstalk: Better than -90 dB @ 1 kHz
Wow and Flutter: Unmeasurable
Analog Inputs/Outputs
Connectors:
Balanced: Single 56 Pin ELCO connector block
Unbalanced: Sixteen 1/4″ phone jacks (8 input, 8 output)
Input Impedance:
Balanced: 10 k ohms
Unbalanced: 11 k ohms
Output Impedance:
Balanced: 510 ohms
Unbalanced: 510 ohms
Nominal Input Levels
Balanced: +4 dBu
Unbalanced: -10 dBV
Maximum Input Levels:
Balanced: +19 dBu
Unbalanced: +5 dBV
Digital Inputs/Outputs
Connectors: Two EIAJ fiber optic jacks (1 input, 1 output)
Communications Protocol: Alesis Fiberoptic Multichannel (8 tracks)
Remote/Sync
Remote Control Connectors: Two 1/4″ phone jacks (transport Remote Control and/or Locate/Play footswitch jack and Punch In/Out footswitch jack)
User Remote Functions Accessible (and available on LRC): Play, Stop, Fast Forward, Rewind, Record, Locate 0, Locate 1, Locate 2, Set Locate, Auto 2-1, Auto Play, Auto Input Monitor and All Input Monitor
Sync Connectors: Two 9 pin D-Sub connectors (Sync In and Sync Out)
Sync Capability: Automatic Master/Slave Syncing between up to 16 ADATs (128 audio tracks)
General
Front Panel Controls and Indicators: Transport controls and LED indicators for Play, Stop, Fast Forward, Rewind , Record and Eject. Record Enable pushbuttons and LED indicators for channels 1 thru 8. Pushbuttons for Set Locate, Locate 0, Locate 1, Locate 2. Pushbuttons and LED indicators for Auto 2-1, Auto Play, Pitch Up (+100 cents), Pitch Down (-300 cents), Format Tape, Digital/Analog Input, Auto Input Monitor and All Input Monitor. 15 segment LED level display for channels 1 thru 8 (0 to -60 dB range). 7 segment LED display indicates tape position (time) or pitch change. AC Power pushbutton.
Rear Panel Controls and Connectors: Sixteen 1/4″ phone jacks for unbalanced inputs and outputs (8 in, 8 out), One 56 Pin ELCO connector block for all balanced inputs and outputs. Two fiberoptic connectors for digital input and output, three 9 pin D-Sub connectors for external Sync In, Sync Out and Meter Bridge , two 1/4″ phone jacks for LRC Remote Controller and for Punch In/Out and Locate/Play footswitches.
Power Requirements: 90-250 VAC, 50-60 Hz, 50 W maximum
Operating Temperature: 10-40_ C for specified performance
Operating Humidity: 80% maximum with no dew condensation for specified performance
Dimensions (H x W x D): 5 1/4″ x 19″ x 14″ (127mm x 483mm x 56mm), 3U IEC rack mounting
Weight:15 lbs (6.8 kg)